i-smartphone FAQs

Posted By admin
Categoirzed Under: Support
Comments (0)

FAQs:

  • Message on itunes “SIM Card inserted not supported”

    Simply switch on Air Plane mode on you iPhone before plugging into itunes. Go to Settings>Airplane Mode.This simply switches of the Simcard whilst you sync your music.
    This only effects some users.

  • Do you ship worldwide ?

    Yes. We use DHL Air mail which normal takes 3 days to deliver.

  • Which Countries / Networks are supported

    All networks in every country are supported. If in the event your network does not work we will offer a full refund and post details here for other users. As of yet we have had no reports back stating that it does not work.

  • Does your simcard work with iPhone 3G v2.1

    Yes, Our device is the only solution which lets you upgrade as normal when Apple release new versions.

  • Does my iPhone have to be activated

    In order to use our sim, the phone must be activated . This is very easy to do and we provide full instructions in the pack when delivered. Our recommended method is to use the original sim card that was supplied with the iPhone 3G. If however, you do not have this sim then we can provide you with instructions on how to activate the phone.

  • Will this definitely unlock the iPhone 3g

    YES, This has been tested on over 1000 iphone 3g’s.This is the only solution at the moment to unlock you iphone 3g for use on any network with 3g data access enabled. There is no software unlock as yet.

    Some other companies claim to unlock your phone but you can not enable the 3g data and every now and again the phone signal drops and you are required to remove your sim and place in another phone. This can happen 3-4 time a week.

  • Can i use the internet GPRS, EDGE, HSPDA, and 3g on my iPhone 3G?

    Yes. GPRS, EDGE, HSPDA and 3G all work fine on your Phone. We are the only unlocking device on the market to day which allows the phone to use 3g data. All the other deviceson the market require you to turn off 3g on your phone before getting a signal.

  • About “no sim”

    The connection problem on the chip, There are six little metal pieces on the chip showing on the picture. “6 Metal pieces”, Recently we have been requested to make the chips soft and thin, It causes the electronic contact to be too flat and small, That’s why some iphone 3G  have “NO SIM” problem, the reason is that the phone sim card and the unlock sim card are not connected, the basic solution is to make those 6 metal pieces and the sim card fully connected. For example, pressing into the card trough, the clean SIM card copper, ,make them completely connected, finally achieve the unlocking goal! We apologize for the inconvenience.

iPhone Firmware 2.1

Posted By admin
Categoirzed Under: iPhone 3G Firmware
Comments (0)

iPhone 2.1
As promised by Apple at Tuesday’s Let’s Rock event, the iPhone 2.1 software update is now available for iPhone.

The update includes many bug fixes and improvements, including:

  • Decrease in call drops.
  • Significantly improved battery life for most users (our emphasis).
  • Improved back-up speed.
  • Faster app installation.
  • Improved accuracy of 3G signal strength display.
  • Option to wipe data after ten failed passcode attempts.
  • Genius playlist creation.

Security content for the update is available at Apple’s website.

Those of you waiting for something bigger, such as true iPhone GPS, will have to be content, at least for now, with an iPhone that simply works better.

The 231MB iPhone 2.1 update is free for all iPhone users, and is available through iTunes.

Product [iPhone 2.1]

for 2G:http://appldnld.apple.com.edgesuite.net/content.info.apple.com/iPhone/061-5202.20080909.gkbEj/iPhone1,1_2.1_5F136_Restore.ipsw
for 3G:http://appldnld.apple.com.edgesuite.net/content.info.apple.com/iPhone/061-5198.20080909.K3294/iPhone1,2_2.1_5F136_Restore.ipsw

WinPwn 2.5-Beta 2 Update released (08/31/08)

Posted By admin
Categoirzed Under: iPhone 3G Firmware
Comments (0)

WinPwn 2.5.0.2

- QuickPwn Support for 2.0/2.0.1/2.0.2
- Root partition resize support
- Installer support
- Basic / Expert modes
- Wizard style interface
- Automatic updater
- Support for WinXP and Vista 32/64bit.

Upgrade:
- Just click the pineapple and select check for upgrades to upgrade!

Notes:

- Why is it beta? Well it’s my way of saying.. Use at your own risk
- You MUST do a full uninstall of winpwn 1/2 before installing the new version
- Make sure you have the latest version of iTunes (Currently 7.7)

Bug fixes

- Crash when building ipsw
- Quickpwn crash bug fix

Download 2.5.0.2